Home
About Us
Company Profile
Enterprise culture
Qualification Certification
Development process
Products
Oil-free air compressor
DC air compressor
AC air compressor
Vacuum pump
Air System Solutions
Rail Transit Industry
Laboratory Testing
New energy electric bus
Nitrogen generator
Medical industry
Dental therapeutic apparatus
Portable compressor solution
Post-processing equipment
Adsorption dryer
Membrane dryer
Filter
Hydrogen Energy Solutions
AD-SALE
AST
System Accessories
Electric proportional valve
Hydraulic proportional valve
Pressure Sensors/Transmitters
Mass flow meter/controller
Pressure switch
Level switch
Flow switch
Metal powder sintering
Other
Application
Aerospace
Textile
Pharmaceutical Industry
Refrigeration industry
Rail Transit
Water Treatment & Sewage Treatment
Food & Beverage
Chemical reagent
Automotive industry
Tire manufacturing
Die casting industry
News
Company News
Industry dynamics
Technical exchange
Contact Us
Online message
Recruitment Information
中文
English
Application of Proportional Electric Proportional Valve on PC Board Scraper
The PC board fabrication machine uses a doctor blade to control the thickness of solder applied to the board. In this very sensitive application, the force of the doctor blade must be kept constant. High resolution and repeatability are a must. This sketch shows the QPV1 controlling the pressure of the Air-Pel cylinder. These are frictionless glass-lined cylinders used to control the force on the scraper. They achieve this "frictionless" state by letting some air escape constantly. This makes the gas pressure application a "constant flow" process, which is ideal for QPVs at these flow rates. The manufacture of thick film ceramics also has similar requirements for doctor blade applications. QPV1 is suitable for both applications due to its high resolution (up to +/-0.005% of full scale) and repeatability of +/-0.02% of full scale calibration.
11
2024
/
03
Application of Proportional electric proportional valve in steel cleaning and oiling
Steel cleaning requires a moderate amount of force. During this process, Proportion-Air QB3 provides force control to the brush, while QB2 pressurizes the liquid regulator to atomize the steel and re-oil. QB3 is controlling the strength of the brush roll, which cleans the steel plate before it is stamped. QB2 is then used to control the pressure of the liquid regulator to re-oil the steel and prevent oxidation. QB2 uses a second loop feedback scheme to measure the oil pressure as it enters the nozzle. This means that pressure is always ideal for consistent spraying.
Application of Proportional Electric Proportional Valve in Pneumatic Torque Gun Control
Pneumatics can be used to provide precise, simple and repeatable remote torque gun control. In this sketch, QB2 is guiding the PSR series amplifier, which controls the pressure of the torque gun. The torque sensor provides direct feedback to the QB2. This feedback uses a 0-10 VDC analog signal that represents the entire torque range of the sensor. QB2 is calibrated at 0-10 VDC = 0-100 PSI-in this case, 100 PSI will produce the maximum torque on the torque gun. The customer's process uses 6 specific torques, so a selector switch is used to provide 6 specific output VDCs. These VDCs are command signals to QB2. In this process, a 50% command to QB2 will be equivalent to 50% (torque gun capacity) torque.
Proportional Electric Proportional Valve to Control Pressure in Laser Cutting
Precision laser cutting requires the use of precision electronic regulators and controls. Proportion-Air offers a range of custom systems for regulating pressure in high-tech laser equipment. Applications include: Adjustment of gas mixtures in laser charging chambers Adjust the cutting machine pressure according to the cutting material. Auxiliary gas regulation of automatic laser welding equipment Gas mixing adjustment Laser cutting is the main application of our regulators. You need low-pressure oxygen to pierce the metal, and then high-pressure nitrogen to achieve a clean cut. When the laser cuts, oxygen helps burn the metal. Once the surface is pierced, switch to another gas (such as nitrogen) to keep it clean-a bit like blowing metal shavings aside to keep the cutting chips away. This precision cutting means that you do not have to further process any edge parts, thereby maximizing the efficient and economical use of materials. The normal valves that deliver these gases simply open and close without proportional adjustment. Their job is to choose the right gas based on the content of the laser cut. The work of our equipment is proportionally through mixed gases. The computer will tell our equipment when cutting, what the pressure to keep clean should be, and it will constantly adjust. In order to eliminate the possibility of fire, our equipment is nickel-plated brass instead of aluminum, which is important when dealing with excess oxygen. In addition, we remove all petroleum products from the regulator and only use lubricants that are compatible with oxygen. Before applying an oxygen-compatible lubricant, we use ultrasonic baths and other methods to verify the elimination of residues. Accuracy with repeatability Our valves not only provide safety and precision, but this precision is extremely repeatable. They are proven commodities. Our customers will tell you that our laser cut proportional valves are the most reliable in the industry.